A comparative study on the performance of sinking and milling micro-EDM for nanofinishing of tungsten carbide

A comparative study on the performance of sinking and milling micro-EDM for nanofinishing of tungsten carbide

10.1504/IJNM.2010.034783

Saved in:

書目詳細資料
Main Authors:	Jahan, M.P., Wong, Y.S., Rahman, M.
其他作者:	MECHANICAL ENGINEERING
格式:	Article
出版:	2014
主題:	Average surface roughness Electrode wear ratio Material removal rate Milling micro-EDM Nanofinishing Peak-to-valley roughness Sinking micro-EDM Surface topography Tungsten carbide
在線閱讀:	http://scholarbank.nus.edu.sg/handle/10635/84772
標簽:	添加標簽沒有標簽, 成為第一個標記此記錄!
機構:	National University of Singapore

相似書籍

An experimental investigation on the surface characteristics of tungsten carbide for the fine-finish die-sinking and scanning micro-EDM
由: Jahan, M.P., et al.
出版: (2014)

MICRO-EDM-BASED MULTI-PROCESS MACHINING OF TUNGSTEN CARBIDE
由: MUHAMMAD PERVEJ JAHAN
出版: (2010)

Migration of materials during finishing micro-EDM of tungsten carbide
由: Jahan, M.P., et al.
出版: (2014)

A STUDY OF THE OPTIMUM PARAMETERS IN EDM MACHINING OF TUNGSTEN CARBIDE MATERIAL
由: KHIN MOE AYE
出版: (2020)

A study on the fine-finish die-sinking micro-EDM of tungsten carbide using different electrode materials
由: Jahan, M.P., et al.
出版: (2014)

A review on the conventional and micro-electrodischarge machining of tungsten carbide
由: Jahan, M.P., et al.
出版: (2014)

Study of micro-EDM of tungsten carbide with workpiece vibration
由: Jahan, M.P., et al.
出版: (2014)

Nanofinishing of hard materials using micro-electrodischarge machining
由: Jahan, M.P., et al.
出版: (2014)

Study on the nano-powder-mixed sinking and milling micro-EDM of WC-Co
由: Jahan, M.P., et al.
出版: (2014)

Study of the effect of machining parameters on the machining characteristics in electrical discharge machining of tungsten carbide
由: Lee, S.H., et al.
出版: (2014)

A study on the quality micro-hole machining of tungsten carbide by micro-EDM process using transistor and RC-type pulse generator
由: Jahan, M.P., et al.
出版: (2014)

An Experimental Investigation on Surface Characteristics of Tool Steel using Powder Mixed Micro-EDM
由: MOHAMMED MUNTAKIM ANWAR
出版: (2010)

On-machine fabrication of high-aspect-ratio micro-electrodes and application in vibration-assisted micro-electrodischarge drilling of tungsten carbide
由: Jahan, M.P., et al.
出版: (2014)

Modelling and experimental investigation on the effect of nanopowder-mixed dielectric in micro-electrodischarge machining of tungsten carbide
由: Jahan, M.P., et al.
出版: (2014)

Influences of pulsed power condition on the machining properties in micro EDM
由: Son, S., et al.
出版: (2014)

Development, modeling, and experimental investigation of low frequency workpiece vibration-assisted micro-EDM of tungsten carbide
由: Jahan, M.P., et al.
出版: (2014)

Study of the diffusion of carbon, its sources, and effect on finishing micro-EDM performance of cemented carbide
由: Jahan, M.P., et al.
出版: (2014)

Fabrication of EDM electrodes by localized electrochemical deposition
由: Habib, M.A., et al.
出版: (2014)

Micro-Electro Discharge Machining (μEDM)
由: Jahan, M.P., et al.
出版: (2014)

Performance analysis of EDM electrode fabricated by localized electrochemical deposition for micro-machining of stainless steel
由: Habib, M.A., et al.
出版: (2014)

Study of Micro-grinding of Glass using On-machine Fabricated Polycrystalline Diamond (PCD) by Micro-EDM
由: ASMA PERVEEN
出版: (2012)

Study of the surface integrity of the machined workpiece in the EDM of tungsten carbide
由: Lee, S.H., et al.
出版: (2014)

Experimental investigations into the influence of major operating parameters during micro-electro discharge drilling of cemented carbide
由: Jahan, M.P., et al.
出版: (2014)

Transitions of micro-EDM/SEDCM/micro-ECM milling in low-resistivity deionized water
由: Nguyen, M.D., et al.
出版: (2014)

Tool-based nanofinishing and micromachining
由: Rahman, M., et al.
出版: (2014)

Evaluation of the effectiveness of low frequency workpiece vibration in deep-hole micro-EDM drilling of tungsten carbide
由: Jahan, M.P., et al.
出版: (2014)

Development of localized electrochemical deposition process for the fabrication of on-machine micro-EDM electrode
由: MOHAMMAD AHSAN HABIB
出版: (2010)

Tool-based micro-machining
由: Asad, A.B.M.A., et al.
出版: (2014)

Performance evaluation of cryogenically treated tungsten carbide tools in turning
由: Yong, A.Y.L., et al.
出版: (2014)

Characteristics of high speed micro-cutting of tungsten carbide
由: Liu, K., et al.
出版: (2014)

A comparative experimental investigation of deep-hole micro-EDM drilling capability for cemented carbide (WC-Co) against austenitic stainless steel (SUS 304)
由: Jahan, M.P., et al.
出版: (2014)

Micro-ball endmilling of tungsten carbide for micro-molding and prototyping applications
由: Arif, M., et al.
出版: (2014)

CBN tool wear in ductile cutting of tungsten carbide
由: Liu, K., et al.
出版: (2014)

Investigation of micro-EDM material removal characteristics using single RC-pulse discharges
由: Wong, Y.S., et al.
出版: (2014)

Integrated hybrid micro/nano-machining
由: Rahman, M., et al.
出版: (2014)

Simultaneous micro-EDM and micro-ECM in low-resistivity deionized water
由: Nguyen, M.D., et al.
出版: (2014)

Performance of cryogenically treated tungsten carbide tools in milling operations
由: Yong, A.Y.L., et al.
出版: (2014)

Performance evaluation of cryogenically treated tungsten carbide cutting tool inserts
由: Seah, K.H.W., et al.
出版: (2014)

An experimental investigation into the micro-electrodischarge machining behavior of p-type silicon
由: Jahan, M.P., et al.
出版: (2014)

An experimental investigation of single and multi-tool micro-EDM
由: MASHEED AHMAD
出版: (2010)