Characterization of the droplet formation phase for the H2O-LiBr absorber : an analytical and experimental analysis

The poor heat and mass transfer occurring in the H2O–LiBr absorber is one of the main limitations towards reducing the size of absorption chillers. Previous research shows that, as droplets form at the base of the absorber pipes, considerably large mass transfer coefficients can be obtained. However...

Full description

Saved in:
Bibliographic Details
Main Authors: Cola, Fabrizio, Hey, Jonathan, Romagnoli, Alessandro
Other Authors: School of Mechanical and Aerospace Engineering
Format: Article
Language:English
Published: 2020
Subjects:
Online Access:https://hdl.handle.net/10356/140837
Tags: Add Tag
No Tags, Be the first to tag this record!
Institution: Nanyang Technological University
Language: English
id sg-ntu-dr.10356-140837
record_format dspace
spelling sg-ntu-dr.10356-1408372020-06-02T07:04:54Z Characterization of the droplet formation phase for the H2O-LiBr absorber : an analytical and experimental analysis Cola, Fabrizio Hey, Jonathan Romagnoli, Alessandro School of Mechanical and Aerospace Engineering Engineering::Mechanical engineering Absorption Adiabatic Absorber The poor heat and mass transfer occurring in the H2O–LiBr absorber is one of the main limitations towards reducing the size of absorption chillers. Previous research shows that, as droplets form at the base of the absorber pipes, considerably large mass transfer coefficients can be obtained. However, modeling this phase of droplet formation has not been fully explored, as most of the research focuses on the film flow process preceding the droplet formation. The present study focuses on two aspects. Firstly, the dynamics of the droplet formation is investigated, with a focus on the effect of the solid surface shape on the droplet formation. A model to describe the droplet profile geometry was developed using the Euler-Lagrange equation and validated against experimental tests. Several pin geometries were tested and the results have shown that a 120° rhomboidal geometry is more suitable to increase the liquid-vapor interface area, while lowering the risk of droplet coalescence. Secondly, an analytical heat and mass transfer model based on the Fourier Series method has been developed to study the influence of pin size on the absorption process in an adiabatic absorber. The results show that the optimum width of the 120° rhomboidal pin is found at 6 mm, which maximizes the water absorbed during the droplet formation phase, without excessive use of material. The common assumption that treats the forming droplet as a half sphere fails to capture changes in the pin-droplet interaction which adversely affects the model accuracy. The proposed model shows that for pin widths smaller than 6 mm, the absorption process is impaired by the lower surface area exposed to the water vapor, resulting in up to 67% less mass absorbed obtainable and a decrease in the cooling power obtainable. In more practical terms, a rated 3 kW of cooling power is used as a case study with a 6 mm pin which reduces the absorber volume by 30% with respect to an absorber with 3 mm wide pins. This shows that by treating the droplet formation phase with a more physically-sound geometrical domain can improve the accuracy of the absorption models and can be easily implemented with any programming language to help in the design optimization of the absorber. 2020-06-02T07:04:54Z 2020-06-02T07:04:54Z 2018 Journal Article Cola, F., Hey, J., & Romagnoli, A. (2018). Characterization of the droplet formation phase for the H2O-LiBr absorber : an analytical and experimental analysis. Applied Energy, 222, 885-897. doi:10.1016/j.apenergy.2018.03.035 0306-2619 https://hdl.handle.net/10356/140837 10.1016/j.apenergy.2018.03.035 2-s2.0-85045612643 222 885 897 en Applied Energy © 2018 Elsevier Ltd. All rights reserved.
institution Nanyang Technological University
building NTU Library
country Singapore
collection DR-NTU
language English
topic Engineering::Mechanical engineering
Absorption
Adiabatic Absorber
spellingShingle Engineering::Mechanical engineering
Absorption
Adiabatic Absorber
Cola, Fabrizio
Hey, Jonathan
Romagnoli, Alessandro
Characterization of the droplet formation phase for the H2O-LiBr absorber : an analytical and experimental analysis
description The poor heat and mass transfer occurring in the H2O–LiBr absorber is one of the main limitations towards reducing the size of absorption chillers. Previous research shows that, as droplets form at the base of the absorber pipes, considerably large mass transfer coefficients can be obtained. However, modeling this phase of droplet formation has not been fully explored, as most of the research focuses on the film flow process preceding the droplet formation. The present study focuses on two aspects. Firstly, the dynamics of the droplet formation is investigated, with a focus on the effect of the solid surface shape on the droplet formation. A model to describe the droplet profile geometry was developed using the Euler-Lagrange equation and validated against experimental tests. Several pin geometries were tested and the results have shown that a 120° rhomboidal geometry is more suitable to increase the liquid-vapor interface area, while lowering the risk of droplet coalescence. Secondly, an analytical heat and mass transfer model based on the Fourier Series method has been developed to study the influence of pin size on the absorption process in an adiabatic absorber. The results show that the optimum width of the 120° rhomboidal pin is found at 6 mm, which maximizes the water absorbed during the droplet formation phase, without excessive use of material. The common assumption that treats the forming droplet as a half sphere fails to capture changes in the pin-droplet interaction which adversely affects the model accuracy. The proposed model shows that for pin widths smaller than 6 mm, the absorption process is impaired by the lower surface area exposed to the water vapor, resulting in up to 67% less mass absorbed obtainable and a decrease in the cooling power obtainable. In more practical terms, a rated 3 kW of cooling power is used as a case study with a 6 mm pin which reduces the absorber volume by 30% with respect to an absorber with 3 mm wide pins. This shows that by treating the droplet formation phase with a more physically-sound geometrical domain can improve the accuracy of the absorption models and can be easily implemented with any programming language to help in the design optimization of the absorber.
author2 School of Mechanical and Aerospace Engineering
author_facet School of Mechanical and Aerospace Engineering
Cola, Fabrizio
Hey, Jonathan
Romagnoli, Alessandro
format Article
author Cola, Fabrizio
Hey, Jonathan
Romagnoli, Alessandro
author_sort Cola, Fabrizio
title Characterization of the droplet formation phase for the H2O-LiBr absorber : an analytical and experimental analysis
title_short Characterization of the droplet formation phase for the H2O-LiBr absorber : an analytical and experimental analysis
title_full Characterization of the droplet formation phase for the H2O-LiBr absorber : an analytical and experimental analysis
title_fullStr Characterization of the droplet formation phase for the H2O-LiBr absorber : an analytical and experimental analysis
title_full_unstemmed Characterization of the droplet formation phase for the H2O-LiBr absorber : an analytical and experimental analysis
title_sort characterization of the droplet formation phase for the h2o-libr absorber : an analytical and experimental analysis
publishDate 2020
url https://hdl.handle.net/10356/140837
_version_ 1681058828132548608