Effect of moisture on the curing and processing behaviour of an epoxy underfill system

Effect of moisture on the curing and processing behaviour of an epoxy underfill system

This project sought to evaluate two cases of water contamination on the processing behaviour and the thermo-mechanical properties of an anhydride cured cycloaliphatic epoxy resin commonly used in underfill formulations. In this study, known amounts of water were deliberately introduced into underfil...

Saved in:

書目詳細資料
主要作者:	Lim, Sin Heng.
其他作者:	Chian, Kerm Sin
格式:	Theses and Dissertations
出版:	2008
主題:	DRNTU::Engineering::Manufacturing
在線閱讀:	http://hdl.handle.net/10356/6027
標簽:	添加標簽沒有標簽, 成為第一個標記此記錄!
機構:	Nanyang Technological University

相似書籍

Effect of moisture uptake on processing of underfill encapsulant materials
由: Goh, Seach Hwee.
出版: (2008)

Modelling of microwave curing process for flip chip underfill materials
由: Liu, Lie.
出版: (2008)

An investigation on flip chip underfill delamination
由: Lee, Bryan Sik Pong.
出版: (2008)

Machine-vision guided underfill dispense system for direct chip attach electronics packages
由: Wong, Jordan How Tho.
出版: (2009)

Cure of underfills in flip chips using microwave
由: Yi, S., et al.
出版: (2014)

Chemothermal modeling and finite-element analysis for microwave cure process of underfill in flip-chip packaging
由: Liu, L., et al.
出版: (2014)

Finite element analysis for microwave cure of underfill in flip chip packaging
由: Liu, L., et al.
出版: (2014)

Thermal curing of composites based epoxy
由: Lia Wijayanti Pratomo.
出版: (2010)

Optimizing epoxy curing in fibre reinforced polymers
由: Lim, Cecilia Meng Li
出版: (2016)

UV curing of a new epoxy formulation - kinetics multifunctional epoxy / cyclo epoxy adipate
由: Yu, Xilan.
出版: (2009)

Microwave curing of a filled epoxy system for rapid prototyping application
由: Kwek, Hian Beng.
出版: (2008)

Microwave curing of epoxy-amine system - effect of curing agent on the rate enhancement
由: Boey, F.Y.C., et al.
出版: (2014)

Optimization of pultrusion of composites with post-curing
由: Soe Moe Kyaw.
出版: (2008)

Feasibility study of a quick cure process using a conventional belt furnace
由: Kwan, Yew Kee.
出版: (2009)

Simultaneous catalyzing and reinforcing effects of imidazole-functionalized graphene in anhydride-cured epoxies
由: Liu, Wanshuang, et al.
出版: (2013)

Numerical simulation of the flip-chip underfilling process
由: Tay, A.A.O., et al.
出版: (2014)

Demolding mechanics of micro-cast UV cured thermosets
由: Yeo, Lip Pin
出版: (2014)

Literature survey : Moisture sportion of nylon
由: Chua, Jian Wei.
出版: (2010)

MICROWAVE RADIATION CURING OF EPOXY/DIAMINE SYSTEMS
由: YAP BOON HUEY
出版: (2020)

Variable frequency microwave (VFM) curing for PBGA and FSBGA packages
由: Chua, Riwis Ian Ping.
出版: (2008)

Curing mechanism study for dual cure of epoxy adhesive by differential scanning calorimetry
由: Waefatimah Weanawae, et al.
出版: (2018)

Experimental modeling for optimal accelerated curing of some Epoxy-Anhydride based filled resin systems
由: Qiang, Wei
出版: (2008)

UV/EB curing of epoxy-based composites Epiclon HP-820 and Epolam 5015
由: Seah, Javien Jin Ping.
出版: (2010)

Optimisation of silicon adhesive cure using differential scanning calorimetry analysis
由: Lee, Chow Sim.
出版: (2008)

Curing kinetics of epoxies by thermal and alternative radiation in the application of fibre-reinforced composites
由: Ng, Feng Lin.
出版: (2011)

THE EFFECT OF SILICA ON THE CURE KINETICS OF EPOXY RESIN WITH AROMATIC DIAMINES
由: JULIANA K.C. WONG
出版: (2020)

Studies of anhydride-cured epoxy networks with bonded and unbonded polyhedral oligomeric silsesquioxane (POSS)
由: Teo, Herman Jun Kai
出版: (2011)

Improvement of the UV curing process for the laser lithography technique
由: Fuh, J.Y.H., et al.
出版: (2014)

Temperature and moisture effects on the failure of composites
由: Lim, Bo Qiang
出版: (2019)

Concurrent engineering process modelling and coordination system (CEPCS).
由: Chee, Calvin Fook Yew.
出版: (2011)

ELECTRON BEAM CURING OF EPOXY ACRYLATE COATINGS ON MEDIUM-DENSITYFIBERBOARD
由: Perpustakaan UGM, i-lib
出版: (2008)

Investigation of viscoelastic effects on micro hot embossing process
由: Tan, Chin Jiat
出版: (2014)

Investigation of micro-raman spectroscopy to determine the degree of cure for tiny dot epoxy adhesive
由: Juthaporn Tangkijpaisarn, et al.
出版: (2018)

Integrating statistical process control and enterprise resource planning systems in a computer integrated manufacturing environment
由: Sim, Norman Boon Heng.
出版: (2008)

A development process planning and management system for concurrent engineering
由: Liau, Hon Chung.
出版: (2009)

Kinetika Reaksi Curing Resin Epoksi Dengan Heksametilendiamin = Kinetics of Curing Reaction of Epoxy Resin with Hexamethylenediantine
由: Perpustakaan UGM, i-lib
出版: (2004)

Contextual influence on productivity behaviour of manufacturing firms in Singapore : an empirical study
由: Lee, Tuck Suen.
出版: (2009)

A study of friction behaviour and lubricant thickness effects in head disk interface
由: Gan, Wuxing
出版: (2009)

Reduction of production lead time in metal injection molding (MIM) process
由: Diao, Zongjie, et al.
出版: (2014)

Effect of a fluoroalkyl-functional curing agent on the wettability, thermal and mechanical properties of hydrophobic biobased epoxy coatings
由: Bellido-Aguilar, Daniel Angel, et al.
出版: (2020)